<div dir="ltr">Hi Barry,<div><br></div><div>I have changed my config based on your recommendation and can see calls flowing but no answer. I will continue later later today and feedback once working.</div><div><br></div><div>
Thanks.</div><div><br></div><div>Tabi</div></div><div class="gmail_extra"><br><br><div class="gmail_quote">On Wed, Apr 30, 2014 at 12:17 PM, Tabi Tabe Tabi <span dir="ltr"><<a href="mailto:tabi.tabe@gmail.com" target="_blank">tabi.tabe@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr">Thanks Barry.<div><br></div><div>I will give it a short and feedback to the group.</div><div><br></div><div>
Regards,</div><div><br></div><div>Tabi</div></div><div class="gmail_extra"><div><div class="h5"><br><br><div class="gmail_quote">
On Wed, Apr 30, 2014 at 11:46 AM, Barry Flanagan <span dir="ltr"><<a href="mailto:barry@flanagan.ie" target="_blank">barry@flanagan.ie</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div dir="ltr"><div>On 30 April 2014 10:29, Tabi Tabe Tabi <span dir="ltr"><<a href="mailto:tabi.tabe@gmail.com" target="_blank">tabi.tabe@gmail.com</a>></span> wrote:<br></div><div class="gmail_extra"><div class="gmail_quote">
<div>
<blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex"><div dir="ltr">Hi,<div><br></div><div>I read in one of the emails that it is possible to setup a subscriber to connect to SPCE with IP address authentication, instead of SIP username and password. I am trying to do that but realized that the subscriber account requires SIP username and password.</div>
</div></blockquote><div><br></div></div><div>It is required to enter one, but it does not have to be used if you set Trusted Source and a Permanent Registration.</div><div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">
<div dir="ltr">
<div><br></div><div>I have setup a subscriber with a DID and tested with a polycom phone and it can make outboud and receive inbound calls no problem. On the same account, tried using on an IP PBX which only support IP authentication SIP trunk without SIP username and password and it fails. It can neither receive nor make calls. Here is what I did:</div>
<div><br></div><div>Subscriber--->Details --> Preferences --->Trusted Source . Here I added the IP address of the IP PBX (both are in the same LAN and Subnet)</div><div><br></div></div></blockquote><div><br></div>
</div><div>I presume you also included the Protocol and a From Pattern such as "^sip:.*"</div><div><br></div><div>If the Trusted source was set up correctly, you should have been able to at least make outbound calls from your PBX. If not you need to provide some logs.</div>
<div>
<div> </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex"><div dir="ltr"><div></div><div>Then I enabled E164_to_RURI here:</div>
<div><div>Subscriber--->Details --> Preferences --->Number Manipulation</div><div><br></div><div>By making the changes above, I assume that SPCE will not expect the PBX to send username and password and will process the calls. Also, all calls made to the DID will be routed to the PBX.</div>
<div><br></div></div></div></blockquote><div><br></div></div><div>The above will only make it so that SPCE does not require authentication when the PBX makes an outbound call. To get inbound working you need also to create a Permanent Registration for this peer - this tells SPCE where to send calls for this subscriber without the subscriber needing to register itself.</div>
<div><br></div><div>Go to </div><div><br></div><div>Subscriber---> Details --> Registered Devices -> Create Permanent Registration<br></div><div><br></div><div>and enter in something like:</div>
<div><br></div><div>sip:username@ip_address:5060<br></div><div><br></div><div>Where username can be anything (but we would usually keep it the same as the subscriber username) and the IP address the IP of the PBX.</div><div>
<div><br></div><div> </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex"><div dir="ltr"><div><div>
</div><div>I have the PBX working fine with Gendband S3 as a reference. Am I doing something wrong or did I miss a step?</div><div><br></div><div>You feedback is much appreciated.</div></div></div></blockquote><div><br></div>
</div><div>Hope this helps.</div><div><br></div><div>-Barry</div><div> </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">
<div dir="ltr"><div><div><br></div><div>Regards,</div><span><font color="#888888">
<div><br></div><span><font color="#888888"><div><br></div>-- <br>...Tabi<div><br></div>
</font></span></font></span></div></div><span><font color="#888888">
<br>_______________________________________________<br>
Spce-user mailing list<br>
<a href="mailto:Spce-user@lists.sipwise.com" target="_blank">Spce-user@lists.sipwise.com</a><br>
<a href="http://lists.sipwise.com/listinfo/spce-user" target="_blank">http://lists.sipwise.com/listinfo/spce-user</a><br>
<br></font></span></blockquote></div><br></div></div>
</blockquote></div><br><br clear="all"><div><br></div></div></div><span class="HOEnZb"><font color="#888888">-- <br>...Tabi<div><br></div>
</font></span></div>
</blockquote></div><br><br clear="all"><div><br></div>-- <br>...Tabi<div><br></div>
</div>