[Spce-user] Spce set up question!

[Alfonso Lopez]

Andrew thanks for your help again.

Anyone have some tips for setting it up on amazon t1 micro? I tried to restart the ngcp panel and it said failed to restart.

Thanks!

Greenkirby21

Sent from my iPhone

> On Apr 8, 2014, at 2:18 PM, Alfonso Lopez <soccercrzyboy21 at yahoo.com> wrote:
> 
> Thank you so much Andrew! Appreciate your help!
> 
> Sent from my iPhone
> 
>> On Apr 8, 2014, at 2:06 PM, Andrew Pogrebennyk <apogrebennyk at sipwise.com> wrote:
>> 
>> Hello,
>> 
>> it takes sometimes several days to reply, moreover "400 Bad Request: SSL
>> certificate error" doesn't pop up here very often.
>> The admin login URL is https://<ip>:1443/login/admin, I don't know what
>> could have caused the 400 error, try restarting nginx and ngcp-panel.
>> 
>> The networking section in config.yml is not used any more. For SIP and
>> RTP however, you need to set advertised IP to your elastic IP:
>> ngcp-network --set-interface=eth0 --advertised-ip=x.y.z.w
>> ngcpcfg apply
>> 
>> For webrtc, you need to enable ICE in domain preference use_rtpproxy
>> (select there "with rtpproxy as only" or "as extra ICE candidate".
>> That's it, use WS URI: ws://<YOUR_IP>:5060/ws or
>> wss://<YOUR_IP>:1443/wss/sip as your entry point.
>> 
>> Note: this works for browser-to-browser calls, but if you have a mixed
>> environment you should also enable transcoding. E.g., I would set for
>> every new webrtc user we need to set those preferences:
>> srtp_transcoding: Prefer SRTP
>> rtcp_feedback: Prefer AVPF
>> 
>> And then set defaults for all (non-webrtc) users in the domain:
>> srtp_transcoding: Force RTP
>> rtcp_feedback: Force AVP
>> Also you the same settings as in domain for PSTN termination.
>> 
>> Regards,
>> Andrew
>> 
>>> On 08/04/14 20:21, Alfonso Lopez wrote:
>>> Sorry if this is spam! I thought I sent this but I don't see any reply. My apologies, I just joined the list so I wasn't sure if it worked the first time or not!
>>> 
>>> I was wondering if there was a tutorial or anything for setting up sipwise CE on amazon ec2? I am working on a school project and need a easy to set up public server, which is why I chose sipwise!
>>> 
>>> I am having a couple of issues. When I follow the handbook, I get to the part where I need to login to the web console. If I just type in the public IP onto my web browser, I get to the "Self-Administration Login" website. However, when I try the default username and password (administrator), I get "Login failed - Please verify username and password".
>>> 
>>> If I try https://<ip>:1443, I get a pop up to accept the certificate. I hit ok, but then I immediately get 400 Bad Request: SSL certificate error.
>>> 
>>> I noticed after the install (which I didn't get any major failures for), the /etc/ngcp-config/config.yml did not contain "networking". I added the following to it based on another mailing list I came across:
>>> 
>>> networking:
>>>  iaddress: 127.0.0.1
>>>  aaddress: <Public IP address given by amazon ec2>
>>>  eaddress: <ip address for eth0 given by "ip a" command
>>> 
>>> Any help would be appreciated!! Thank you so much 
>>> 
>>> Instance Information:
>>> Debian Squeeze 7.4 64 Bit
>>> Type: t1.micro
>>> sipwise mr 3.2.1
>>> 
>>> 
>>> Finally, if I want to use webrtc, do I need to configure anything in particular?
>>> 
>>> Thanks!
>>> 
>>> Greenkirby21
>>> Sent from my iPhone