[Spce-user] Cisco SPA112 Configuration for SipWise

Paul Smith paul.smith at daneco.co.uk
Fri Sep 9 10:57:59 EDT 2016


Hello,

 
Further to my last e-mail, I have had Cisco support on the phone and using remote desktop for over an hour and they could not solve the problem!

 
I notice that the SPA112 registers as follows:

Cisco/SPA112-1.4.1(002)	sip:xxxxxxxxxxxx at 192.168.1.60:5060

 
 
Is the fact that it is registering with its LAN IP significant as I believe it to be? When I assign the same account to a Zoiper softphone, it registers with the correct external IP address. I am going to experiment with the SPA112 sitting directly on a public IP address and see if it registers with SipWise correctly.

 
Raúl - Gemma will be in touch with those login details soon. I am hoping to at least get a test account running so that you can see our configuration and determine how much support we need!

 
Very best of wishes,

 
Paul.

 
--

Paul R. Smith B.Sc. (Hons.)

Managing Director

Data Network Consultants Limited

 
T:   01207 750 550

W: www.daneco.co.uk <http://www.daneco.co.uk> 

 

 
iNorthumberland's Fixed Wireless Access Partner - Superfast Wireless Network Specialists.

 
DANECO is a trading name of Data Network Consultants Limited.

 
Company Reg. No: 06769055
Registered in England and Wales.

 
This email and its contents are confidential and intended for the addressee only. It may not be disclosed to or used by anyone else nor may it be copied in any way. Data Network Consultants Limited nor the sender accepts any responsibility for viruses and it is the addressee's responsibility to check attachments if any. Any opinions expressed in this email are those of the sender and not necessarily those of Data Network Consultants Limited. If received in error please contact the sender to advise then delete from your system.

 

 
-----Original message-----
From:Paul Smith <paul.smith at daneco.co.uk>
Sent:Thu 08-09-2016 19:19
Subject:[Spce-user] Cisco SPA112 Configuration for SipWise
To:Spce-user at lists.sipwise.com; 
 

Dear All,

 
My apologies if this subject has already been covered, but I wondered if someone could point me in the right direction for a working configuration on the Cisco SPA112?

 
I can place outbound calls fine, but inbound are a no-go. I suspect this is because the SPA112 is registering with its internal IP address rather than that of the WAN connection. I have enabled NAT mapping and keep alive but this hasn't made a difference.

 
Any help would be greatly appreciated.

 
Thank you,

 
Paul.

 
--

Paul R. Smith B.Sc. (Hons.)

Managing Director

Data Network Consultants Limited

 
T:   01207 750 550

W: www.daneco.co.uk <http://www.daneco.co.uk> 

 

 
iNorthumberland's Fixed Wireless Access Partner - Superfast Wireless Network Specialists.

 
DANECO is a trading name of Data Network Consultants Limited.

 
Company Reg. No: 06769055
Registered in England and Wales.

 
This email and its contents are confidential and intended for the addressee only. It may not be disclosed to or used by anyone else nor may it be copied in any way. Data Network Consultants Limited nor the sender accepts any responsibility for viruses and it is the addressee's responsibility to check attachments if any. Any opinions expressed in this email are those of the sender and not necessarily those of Data Network Consultants Limited. If received in error please contact the sender to advise then delete from your system.

 
 


_______________________________________________
 Spce-user mailing list
 Spce-user at lists.sipwise.com
 https://lists.sipwise.com/listinfo/spce-user
 

 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sipwise.com/mailman/private/spce-user_lists.sipwise.com/attachments/20160909/d6d86327/attachment.html>


More information about the Spce-user mailing list