[Spce-user] Spce-user Digest, Vol 35, Issue 4
Edo
edo.ekunwe at gmail.com
Sun May 8 17:11:47 EDT 2022
Hi Leighton,
I checked the rate-o-mat.log and it has no information (0 bytes). Is it
possible that I have not set the rate engine correctly? the cdr.log shows
information and apparently calls being billed but no call-ID information.
see below
sudo cat cdr.log
May 8 00:24:05 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 2 callids and generating 2 CDRs was 61015 us.
May 8 00:24:05 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 32.778825 CDR/sec
May 8 00:25:08 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 66345 us.
May 8 00:25:08 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 15.072726 CDR/sec
May 8 00:25:11 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 2982 us.
May 8 00:25:11 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:25:21 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 2911 us.
May 8 00:25:21 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:25:31 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 3282 us.
May 8 00:25:31 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:25:41 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 2536 us.
May 8 00:25:41 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:25:51 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 3074 us.
May 8 00:25:51 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:26:01 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 2667 us.
May 8 00:26:01 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:26:11 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 50406 us.
May 8 00:26:11 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 19.838908 CDR/sec
May 8 00:26:14 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 3211 us.
May 8 00:26:14 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:26:24 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 2285 us.
May 8 00:26:24 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:26:34 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 2981 us.
May 8 00:26:34 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:26:44 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 3276 us.
May 8 00:26:44 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 00:26:54 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 43391 us.
May 8 00:26:54 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 23.046254 CDR/sec
May 8 15:53:02 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 34636 us.
May 8 15:53:02 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 28.871694 CDR/sec
May 8 15:55:25 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 49914 us.
May 8 15:55:25 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 20.034459 CDR/sec
May 8 15:56:38 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 36547 us.
May 8 15:56:38 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 27.362027 CDR/sec
May 8 15:58:51 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 45959 us.
May 8 15:58:51 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 21.758524 CDR/sec
May 8 15:59:24 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 2 callids and generating 2 CDRs was 50023 us.
May 8 15:59:24 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 39.981608 CDR/sec
May 8 15:59:57 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 51488 us.
May 8 15:59:57 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 19.422001 CDR/sec
May 8 16:01:00 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 3491 us.
May 8 16:01:00 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 16:01:10 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 66117 us.
May 8 16:01:10 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 15.124703 CDR/sec
May 8 16:01:13 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 2571 us.
May 8 16:01:13 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 16:01:23 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 3085 us.
May 8 16:01:23 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 16:01:33 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 0 CDRs was 3012 us.
May 8 16:01:33 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 0.000000 CDR/sec
May 8 16:01:43 spce (info) mediator[1442]: mediator.c:447 [main]: Runtime
for loop processing 1 callids and generating 1 CDRs was 209343 us.
May 8 16:01:43 spce (info) mediator[1442]: mediator.c:449 [main]: Total
CDR creation rate 4.776849 CDR/sec
$
Back <https://192.168.1.39:1443/back>
Show all calls Show outgoing calls only Show incoming calls only
Show 51015203550100250All entries
>From Date: To Date: Search:
#CallerCalleeCLIRBilling zoneStatusStart TimeDurationMOS avgMOS packetlossMOS
jitterMOS roundtripCall-IDCost
Total 0:40:38.659 0.00
173 1XXXXXXXXXX XXXXXXXXXX5777 0 ok 2022-05-08 16:00:56.381 0:00:39.928 0.0
0.0 0.0 0.0 3DSBYkqxuq8TAhsH-CM-Sw.. 0.00
Thanks
On Sun, May 8, 2022 at 2:36 PM Leighton Brennan <leightonbrennan at gmail.com>
wrote:
> If you check the rate-o-mat log it should tell you what the reason for
> this is.
> Most likely the rates you have created don’t match the number in the CDR.
> Rate-o-mat logs are stored in /var/log/ngcp/
>
> It will tell you in this log file what the number is so you can correct
> your billing fee.
>
> Best Regards
> Leighton Brennan
>
> On 8 May 2022, at 20:28, Edo <edo.ekunwe at gmail.com> wrote:
>
>
> Thanks Matthias,
>
> I have set up the billing profile, billing network and added the rates to
> it. However, I cannot get it to actually bill against a call.
>
> I have a subscriber that is under a reseller and domain, the reseller has
> a contact, billing profile and contract. When I make calls from the
> subscriber, I route the calls through a peer (I would also like to bill
> peers as well). After the call is complete, when I check the CDR, I see the
> calls but the cost of the call is always showing 0.00. My problem is how to
> tie the rate to the subscriber or peer as needed so that the balance on the
> reseller/subscriber can be reduced based on the calls completed.
>
> Thoughts?
>
> On Sun, May 8, 2022 at 11:00 AM <spce-user-request at lists.sipwise.com>
> wrote:
>
>> Send Spce-user mailing list submissions to
>> spce-user at lists.sipwise.com
>>
>> To subscribe or unsubscribe via the World Wide Web, visit
>>
>> http://lists.sipwise.com/mailman/listinfo/spce-user_lists.sipwise.com
>> or, via email, send a message with subject or body 'help' to
>> spce-user-request at lists.sipwise.com
>>
>> You can reach the person managing the list at
>> spce-user-owner at lists.sipwise.com
>>
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of Spce-user digest..."
>>
>>
>> Today's Topics:
>>
>> 1. Help with Setting up Billing on CE (Edo)
>> 2. Re: Help with Setting up Billing on CE (Matthias Hohl)
>>
>>
>> ----------------------------------------------------------------------
>>
>> Message: 1
>> Date: Sun, 8 May 2022 00:37:12 -0500
>> From: Edo <edo.ekunwe at gmail.com>
>> To: spce-user at lists.sipwise.com
>> Subject: [Spce-user] Help with Setting up Billing on CE
>> Message-ID:
>> <CAFkRdGvQxoPO-LQRij9FE9G_EFyuWD4ynXj=
>> 6+vinBNo_3oDaQ at mail.gmail.com>
>> Content-Type: text/plain; charset="utf-8"
>>
>> Hi All,
>>
>> I have been fumbling with setting up billing on sipwise CE and have been
>> unsuccessful.
>>
>> Please can someone mentor me? The documentation is not very clear as to
>> how
>> to actually achieve this.
>>
>> Thanks
>>
>> --
>> -----
>> Ekunwe
>> Tel: 601.497.3932
>> -------------- next part --------------
>> An HTML attachment was scrubbed...
>> URL: <
>> http://lists.sipwise.com/pipermail/spce-user_lists.sipwise.com/attachments/20220508/41e9cd3f/attachment-0001.html
>> >
>>
>> ------------------------------
>>
>> Message: 2
>> Date: Sun, 8 May 2022 17:14:12 +0200 (CEST)
>> From: Matthias Hohl <matthias.hohl at telematica.at>
>> To: 'Edo' <edo.ekunwe at gmail.com>, spce-user at lists.sipwise.com
>> Subject: Re: [Spce-user] Help with Setting up Billing on CE
>> Message-ID: <1585704095.1958400.1652022852261.JavaMail.zimbra at mx>
>> Content-Type: text/plain; charset="utf-8"
>>
>> Ifyou could descripe me in detail where you need some help, I could try
>> if I can help you ?
>>
>>
>>
>> Normally it is very simple.
>>
>> Create a Billing Profile via the GUI and upload your billing profile
>> entries via CSV file.
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> Von: Edo <edo.ekunwe at gmail.com>
>> Gesendet: Sonntag, 8. Mai 2022 07:37
>> An: spce-user at lists.sipwise.com
>> Betreff: [Spce-user] Help with Setting up Billing on CE
>>
>>
>>
>> Hi All,
>>
>>
>>
>> I have been fumbling with setting up billing on sipwise CE and have been
>> unsuccessful.
>>
>>
>>
>> Please can someone mentor me? The documentation is not very clear as to
>> how to actually achieve this.
>>
>>
>>
>> Thanks
>>
>>
>>
>>
>> --
>>
>> -----
>>
>> Ekunwe
>> Tel: 601.497.3932
>>
>> -------------- next part --------------
>> An HTML attachment was scrubbed...
>> URL: <
>> http://lists.sipwise.com/pipermail/spce-user_lists.sipwise.com/attachments/20220508/9edf7b59/attachment-0001.html
>> >
>> -------------- next part --------------
>> A non-text attachment was scrubbed...
>> Name: smime.p7s
>> Type: application/pkcs7-signature
>> Size: 5022 bytes
>> Desc: not available
>> URL: <
>> http://lists.sipwise.com/pipermail/spce-user_lists.sipwise.com/attachments/20220508/9edf7b59/attachment-0001.p7s
>> >
>>
>> ------------------------------
>>
>> Subject: Digest Footer
>>
>> Spce-user mailing list
>> Spce-user at lists.sipwise.com
>> http://lists.sipwise.com/mailman/listinfo/spce-user_lists.sipwise.com
>>
>>
>> ------------------------------
>>
>> End of Spce-user Digest, Vol 35, Issue 4
>> ****************************************
>>
>
>
> --
> -----
> Ekunwe
> EDO Network Services, Inc.
> Tel: 601.497.3932
> Fax: 601.979.5931
> --
> Spce-user mailing list
> Spce-user at lists.sipwise.com
> http://lists.sipwise.com/mailman/listinfo/spce-user_lists.sipwise.com
>
>
--
-----
Ekunwe
EDO Network Services, Inc.
Tel: 601.497.3932
Fax: 601.979.5931
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sipwise.com/pipermail/spce-user_lists.sipwise.com/attachments/20220508/1a264c82/attachment-0002.html>
More information about the Spce-user
mailing list