[Spce-user] Remove SDP media-level attribute - direction

Imanol Pardavila imanol.pardavila at ibercom.com
Mon Nov 19 12:35:54 EST 2012


Hi everybody,

Finally it works!.
If somebody has the same problem, I inserted the modification in two places:

/etc/ngcp-config/templates/etc/kamailio/proxy/*proxy.cfg.customtt.tt2*

########################################################################
# Reply route 'base-nat-reply'
########################################################################
onreply_route[REPLY_ROUTE_NAT]
{
         xlog("L_INFO", "NAT-Reply - [% logres_init -%]\n");
         force_rport();

         if(has_body("application/sdp") && ($avp(s:from_faxserver) == 1 
|| $avp(s:to_faxserver) == 1))
         {
             # fix for T.38 to patton faxserver gateway, which chokes on 
upper-case
             xlog("L_INFO", "Rewriting T.38 'UDPTL' to 'udptl' - [% 
logres -%]\n");
             replace_body_all(" UDPTL ", " udptl ");
         }

*if(has_body("application/sdp"))**
**        {**
**             # fix SDP direction attribute for Sonus SBC**
**             xlog("L_INFO", "Removing direction attribute from SDP - 
[% logreq -%]\n");**
**             replace_body_all("a=direction:active\r?\n", "");**
**        }*

         if(status=~"(180)|(183)|2[0-9][0-9]")
...
...

########################################################################
# Branch route 'cli-rtp'
########################################################################
branch_route[BRANCH_ROUTE_CLI_RTP]
...
...
         if($avp(s:callee_uuid) != $null && !is_present_hf("P-Callee-UUID"))
         {
                 xlog("L_INFO", "Setting P-Callee-UUID to 
'$avp(s:callee_uuid)' - [% logreq -%]\n");
                 append_hf("P-Callee-UUID: $avp(s:callee_uuid)\r\n");
         }

*if(has_body("application/sdp"))**
**        {**
**             # fix SDP direction attribute for Sonus SBC**
**             xlog("L_INFO", "Removing direction attribute from SDP - 
[% logreq -%]\n");**
**             replace_body_all("a=direction:active\r?\n", "");**
**        }*

         xlog("L_INFO", "Request leaving server, D-URI='$du' - [% logreq 
-%]\n");
}

I hope it would be helpful for somebody.

Thanks Andreas
Best regards
Imanol

El 14/11/2012 10:20, Andreas Granig escribió:
> Hi,
>
> You might want to remove the newline as well, like this:
>
> replace_body_all("a=directmedia:active\r?\n", "");
>
> Andreas
>
> On 11/14/2012 10:12 AM, Imanol Pardavila wrote:
>> Hi,
>> I was able to remove the directionline,  but the problem is that it
>> leaves an empty line between ptime and oldmediaip and SBC returns "400
>> Bad Request"due to malformed INVITE:
>>
>> a=sendrecv
>> a=ptime:20
>>
>> a=oldmediaip:10.34.240.60
>> a=nortpproxy:yes
>>
>> I tried both:
>> replace_body_all("a=direction:active" ,"");
>> replace_body_all("a=direction:active"  ,"");
>>
>> with same result.
>>
>> How could I remove the empty line?
>>
>> Thanks
>> Best regards
>> Imanol
>>
>> El 09/11/2012 14:05, Imanol Pardavila escribió:
>>> Hi Andreas,
>>> "kamailio.cfg.tt2" file has the following main structure:
>>>
>>> route
>>> ...
>>> route[ROUTE_RELAY]
>>> ...
>>> route[ROUTE_REQUEST]
>>> ...
>>> onreply_route
>>> ...
>>> onsend_route
>>> ...
>>>
>>> I guess that I have to insert something like this:
>>>
>>> if(has_body("application/sdp")
>>> {
>>> 	# fix for Sonus SBC - remove directmedia attribute
>>>          xlog("L_INFO", "Removing directmedia attribute - [% logreq -%]\n");
>>>          replace_body_all(" a=directmedia:active ", "");
>>> }
>>>
>>> But I'm not sure about where to insert it. Could you help me?
>>>
>>> Thanks
>>> Best regards
>>> Imanol
>>>
>>> El 09/11/2012 12:45, Andreas Granig escribió:
>>>> Hi Imanol,
>>>>
>>>> Oh, right, it's added by the proxy then after mediaproxy is engaged. So
>>>> the best place would be the load-balancer config at
>>>> /etc/ngcp-config/templates/etc/kamailio/lb/kamailio.cfg.customtt.tt2.
>>>>
>>>> Andreas
>>>>
>>>> On 11/09/2012 11:49 AM, Imanol Pardavila wrote:
>>>>> Hi Andreas,
>>>>> Looking at my traces I'm sure that endpoints aren't sending this
>>>>> attribute; I've just filtered the first packet with this line on SDP
>>>>> body and it's been sent by CE.
>>>>>
>>>>>    * SDP sent from our SBC to CE:
>>>>>
>>>>>          Session Description Protocol
>>>>>              Session Description Protocol Version (v): 0
>>>>>              Owner/Creator, Session Id (o): Sonus_UAC IN IP4 10.34.241.67
>>>>>              Session Name (s): SIP Media Capabilities
>>>>>              Connection Information (c): IN IP4 10.34.240.60
>>>>>              Time Description, active time (t): 0 0
>>>>>              Media Description, name and address (m): audio 1552 RTP/AVP
>>>>> 0 8 101
>>>>>              Media Attribute (a): rtpmap:0 PCMU/8000
>>>>>              Media Attribute (a): rtpmap:8 PCMA/8000
>>>>>              Media Attribute (a): rtpmap:101 telephone-event/8000
>>>>>              Media Attribute (a): fmtp:101 0-15
>>>>>              Media Attribute (a): sendrecv
>>>>>              Media Attribute (a): ptime:20
>>>>>
>>>>>    * SDP sent from CE to our SBC (following packet in the sequence):
>>>>>
>>>>>          Session Description Protocol
>>>>>              Session Description Protocol Version (v): 0
>>>>>              Owner/Creator, Session Id (o): Sonus_UAC IN IP4 10.34.242.11
>>>>>              Session Name (s): SIP Media Capabilities
>>>>>              Connection Information (c): IN IP4 10.34.242.11
>>>>>              Time Description, active time (t): 0 0
>>>>>              Media Description, name and address (m): audio 30132 RTP/AVP
>>>>> 0 8 101
>>>>>              Media Attribute (a): rtpmap:0 PCMU/8000
>>>>>              Media Attribute (a): rtpmap:8 PCMA/8000
>>>>>              Media Attribute (a): rtpmap:101 telephone-event/8000
>>>>>              Media Attribute (a): fmtp:101 0-15
>>>>>              Media Attribute (a): sendrecv
>>>>>              Media Attribute (a): ptime:20
>>>>>              *Media Attribute (a): direction:active**
>>>>> **            Media Attribute (a): oldmediaip:10.34.240.60**
>>>>> **            Media Attribute (a): nortpproxy:yes*
>>>>>
>>>>> Flow diagram:
>>>>>
>>>>> |endpoint A| ------------- |SBC| ------------- |CE| ------------- |SBC|
>>>>> ------------- |endpoint B|
>>>>>
>>>>> SBC: 10.34.240.60, 10.34.241.67
>>>>> CE: 10.34.242.11
>>>>>
>>>>> Any ideas?
>>>>> Thanks
>>>>> Best regards
>>>>> Imanol
>>>>>
>>>>> El 08/11/2012 20:22, Andreas Granig escribió:
>>>>>> Hi,
>>>>>>
>>>>>> On 11/08/2012 05:25 PM, Imanol Pardavila wrote:
>>>>>>> I'm not sure about who builds SDP? lb, proxy, sems? I guess that the
>>>>>> The SDP is created by the endpoints, not by the CE.
>>>>>>
>>>>>>> idea is create my customtt.tt2 file and use replace_body_all () function
>>>>>>> something like:
>>>>>>>
>>>>>>> # remove direction attribute
>>>>>>> replace_body_all(" a=directmedia:active ", "");
>>>>>>>
>>>>>>> Is it correct?
>>>>>> Not sure about the whitespaces, you might need to leave them out I guess.
>>>>>>
>>>>>> Andreas
>>>>>>
>>>>>>
>>>>>>
>>>>>> _______________________________________________
>>>>>> Spce-user mailing list
>>>>>> Spce-user at lists.sipwise.com
>>>>>> http://lists.sipwise.com/listinfo/spce-user
>>>>>>
>>>>>>
>>>>>> -----
>>>>>> No se encontraron virus en este mensaje.
>>>>>> Comprobado por AVG - www.avg.com
>>>>>> Version: 2012.0.2221 / Base de datos de virus: 2441/5382 - Fecha de publicacion: 11/08/12
>>>>> _______________________________________________
>>>>> Spce-user mailing list
>>>>> Spce-user at lists.sipwise.com
>>>>> http://lists.sipwise.com/listinfo/spce-user
>>>>>
>>>>
>>>> _______________________________________________
>>>> Spce-user mailing list
>>>> Spce-user at lists.sipwise.com
>>>> http://lists.sipwise.com/listinfo/spce-user
>>>>
>>>>
>>>> -----
>>>> No se encontraron virus en este mensaje.
>>>> Comprobado por AVG - www.avg.com
>>>> Version: 2012.0.2221 / Base de datos de virus: 2441/5383 - Fecha de publicacion: 11/08/12
>>
>>
>> _______________________________________________
>> Spce-user mailing list
>> Spce-user at lists.sipwise.com
>> http://lists.sipwise.com/listinfo/spce-user
>>
>
>
> _______________________________________________
> Spce-user mailing list
> Spce-user at lists.sipwise.com
> http://lists.sipwise.com/listinfo/spce-user
>
>
> -----
> No se encontraron virus en este mensaje.
> Comprobado por AVG - www.avg.com
> Version: 2012.0.2221 / Base de datos de virus: 2441/5393 - Fecha de publicacion: 11/13/12

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sipwise.com/mailman/private/spce-user_lists.sipwise.com/attachments/20121119/8f4da728/attachment.html>


More information about the Spce-user mailing list