[Spce-user] UC540

[Christopher Saroli]

You could always telnet into the device and run

Terminal monitor
Debug ccsip messages

This will give you some simple sip debugging on the cisco equipment
Remember to turn off debugging when done

Or you could hire me....lol

---------------------------------
Christopher Saroli
csaroli at isysp.com<mailto:csaroli at isysp.com>

From: Jeremie Chism [mailto:jchism2 at gmail.com]
Sent: Friday, May 03, 2013 9:33 AM
To: Christopher Saroli
Cc: spce-user at lists.sipwise.com
Subject: Re: UC540

All mine are in the US also. I'm thinking this is either not matching up or the incoming dial plan like you stated. A Cisco partner did the equipment and install.  He just wants me to provide service to it. I've just never fooled with one and I get the feeling he doesn't have a clue.

On Friday, May 3, 2013, Christopher Saroli wrote:
Nothing special for the uc500... all my subscribers are in the us so I'm always adding the 1 into sipwise and stripping the 1 out from sipwise.

So my uc500 and any other phone system for that matter that I deal with just gets 10 digits


---------------------------------
Christopher Saroli
csaroli at isysp.com<javascript:_e(%7b%7d,%20'cvml',%20'csaroli at isysp.com');>
[ISS-Logo(Small)]
                                 586-226-7800 (Main Office)
                                 586-884-0800 (Direct)

From: Jeremie Chism [mailto:jchism2 at gmail.com<javascript:_e(%7b%7d,%20'cvml',%20'jchism2 at gmail.com');>]
Sent: Friday, May 03, 2013 9:24 AM
To: Christopher Saroli
Cc: spce-user at lists.sipwise.com<javascript:_e(%7b%7d,%20'cvml',%20'spce-user at lists.sipwise.com');>
Subject: Re: UC540

Thanks.

I think we have it in the incoming dial plan. I will check.

On the rewrite rule did you do something special just for the uc520 or make changes to the UC?

On Friday, May 3, 2013, Christopher Saroli wrote:
Yes I am in the US

Did you add your DIDs to the incoming dial plan on the cisco box and assign them to a destination.

Also could be your rewrite rules, the phone system wont by default take E.164

---------------------------------
Christopher Saroli
csaroli at isysp.com<mailto:csaroli at isysp.com>

From: Jeremie Chism [mailto:jchism2 at gmail.com]
Sent: Friday, May 03, 2013 9:13 AM
To: Christopher Saroli
Cc: spce-user at lists.sipwise.com<mailto:spce-user at lists.sipwise.com>
Subject: Re: UC540

Thanks for the information. Are you in the US?  I have outbound working. Inbound gives me a busy signal.

On Friday, May 3, 2013, Christopher Saroli wrote:
I have a UC520 configured with a sip trunk to sipwise.. What info were you looking for. Here is my sip-ua config if that helps

sip-ua
 credentials username {SUBSCRIBER USERNAME} password 7 13340213051811277A767B realm {SIPWISE IP ADDRESS}
 keepalive target ipv4: {SIPWISE IP ADDRESS}:5060
 authentication username {SUBSCRIBER USERNAME} password 7 053A130E2F585B04485744
 no remote-party-id
 retry invite 2
 retry register 10
 timers connect 100
 timers keepalive active 100
 registrar ipv4: {SIPWISE IP ADDRESS}:5060 expires 200
 sip-server ipv4: {SIPWISE IP ADDRESS}:5060
 host-registrar
!

-----Original Message-----
From: spce-user-bounces at lists.sipwise.com<javascript:_e(%7b%7d,%20'cvml',%20'spce-user-bounces at lists.sipwise.com');> [mailto:spce-user-bounces at lists.sipwise.com<javascript:_e(%7b%7d,%20'cvml',%20'spce-user-bounces at lists.sipwise.com');>] On Behalf Of Jeremie Chism
Sent: Tuesday, April 30, 2013 3:41 PM
To: spce-user at lists.sipwise.com<javascript:_e(%7b%7d,%20'cvml',%20'spce-user at lists.sipwise.com');>
Subject: [Spce-user] UC540

Looking for someone that has configured a uc540 with a sip trunk to sipwise that might be able to share some knowledge.

Sent from my iPhone
_______________________________________________
Spce-user mailing list
Spce-user at lists.sipwise.com<javascript:_e(%7b%7d,%20'cvml',%20'Spce-user at lists.sipwise.com');>
http://lists.sipwise.com/listinfo/spce-user


--
Jeremie Chism
Triton Communications


--
Jeremie Chism
Triton Communications


--
Jeremie Chism
Triton Communications
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sipwise.com/pipermail/spce-user_lists.sipwise.com/attachments/20130503/6423b32f/attachment-0001.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 3129 bytes
Desc: image001.jpg
URL: <http://lists.sipwise.com/pipermail/spce-user_lists.sipwise.com/attachments/20130503/6423b32f/attachment-0001.jpg>