[Spce-user] Outgoing Call - Problem

[Jorge Fresneda - Ibersontel]

Hi Daniel,

What parameter need to look to change this within the subscriber?

Regards
Jorge

El 07/07/2014 10:27, Daniel Grotti escribió:
> Hi,
> looks like your subscriber is setting that From domain.
> Usually, if you register a client to a domain, the From should look like
> as you said:
>
> from: <sip:91111111 at SCPE_DOMAIN>
> to: <sip: 922222222@<SPCE_DOMAIN>
>
> before going to the PEER:
>
> from: <sip:91111111 at SCPE_DOMAIN>
> to: <sip: 922222222@<PEER_IP>
>
>
> Daniel
>
>
>
>
>
> On 07/07/2014 10:18 AM, Jorge Fresneda - Ibersontel wrote:
>> Hi Daniel,
>>
>> The problem is not with the CLI, it is with the @ your-domain. For
>> example:
>>
>>
>> Sipwise Address: 120.23.1.1
>> Address PBX (subscriber): 192.168.1.2
>>
>> When I launch a call from the field is as follows:
>>
>> from: <sip:91111111 at 192.168.1.2>
>> to: <sip: 922222222@<carrier_ip>
>>
>>
>> The from should be <sip:91111111 at 120.23.1.1> for the carrier to accept
>> calls.
>>
>>
>> Thanks
>> Regards,
>> Jorge
>>
>>
>>
>> El 07/07/2014 10:12, Daniel Grotti escribió:
>>> Hi,
>>> could this be the issue ?
>>>
>>>
>>>   From the habndbook:
>>>
>>>      If you do NOT authenticate against a peer host, then the caller
>>> CLI is
>>> put into the From and P-Asserted-Identity headers, e.g. "+4312345"
>>> <sip:+4312345 at your-domain.com>. If you DO authenticate, then the From
>>> header is "+4312345" <sip:your_peer_auth_user at your_peer_auth_realm> and
>>> the P-Asserted-Identity header is as usual like
>>> <sip:+4312345 at your-domain.com>. So for presenting the correct CLI in
>>> CLIP no screening scenarios, your peering provider needs to extract the
>>> correct user either from the From Display-Name or from the
>>> P-Asserted-Identity URI-User.
>>>
>>>
>>>
>>> Otherwise please give us more information about your peer configuration
>>> and the call scenario.
>>>
>>> Daniel
>>>
>>>
>>>
>>> On 07/07/2014 10:04 AM, Jorge Fresneda - Ibersontel wrote:
>>>> Hello,
>>>>
>>>> I have a problem in version 2.8 with outgoing calls. In the from
>>>> field  goes "source@ <pbx_ip>"  instead of  "source@ <sipwise_ip>".
>>>>
>>>> What may be because this problem?
>>>>
>>>> Thank you very much.
>>>> Regards
>>>> Jorge
>>>>
>>>> _______________________________________________
>>>> Spce-user mailing list
>>>> Spce-user at lists.sipwise.com
>>>> http://lists.sipwise.com/listinfo/spce-user
>>> _______________________________________________
>>> Spce-user mailing list
>>> Spce-user at lists.sipwise.com
>>> http://lists.sipwise.com/listinfo/spce-user
>>
>> _______________________________________________
>> Spce-user mailing list
>> Spce-user at lists.sipwise.com
>> http://lists.sipwise.com/listinfo/spce-user
>
> _______________________________________________
> Spce-user mailing list
> Spce-user at lists.sipwise.com
> http://lists.sipwise.com/listinfo/spce-user