[Spce-user] Outgoing Call - Problem

[Daniel Grotti]

Hi,
it's just a guess.
Do you really receive the INVITE from your subscriber with the "wrong"
FROM domain ?
If so, this is something you need to change on subscriber side.
Don't know which parameter you need to set, don't know even the client.

Daniel






On 07/07/2014 10:44 AM, Jorge Fresneda - Ibersontel wrote:
> Hi Daniel,
>
> What parameter need to look to change this within the subscriber?
>
> Regards
> Jorge
>
> El 07/07/2014 10:27, Daniel Grotti escribió:
>> Hi,
>> looks like your subscriber is setting that From domain.
>> Usually, if you register a client to a domain, the From should look like
>> as you said:
>>
>> from: <sip:91111111 at SCPE_DOMAIN>
>> to: <sip: 922222222@<SPCE_DOMAIN>
>>
>> before going to the PEER:
>>
>> from: <sip:91111111 at SCPE_DOMAIN>
>> to: <sip: 922222222@<PEER_IP>
>>
>>
>> Daniel
>>
>>
>>
>>
>>
>> On 07/07/2014 10:18 AM, Jorge Fresneda - Ibersontel wrote:
>>> Hi Daniel,
>>>
>>> The problem is not with the CLI, it is with the @ your-domain. For
>>> example:
>>>
>>>
>>> Sipwise Address: 120.23.1.1
>>> Address PBX (subscriber): 192.168.1.2
>>>
>>> When I launch a call from the field is as follows:
>>>
>>> from: <sip:91111111 at 192.168.1.2>
>>> to: <sip: 922222222@<carrier_ip>
>>>
>>>
>>> The from should be <sip:91111111 at 120.23.1.1> for the carrier to accept
>>> calls.
>>>
>>>
>>> Thanks
>>> Regards,
>>> Jorge
>>>
>>>
>>>
>>> El 07/07/2014 10:12, Daniel Grotti escribió:
>>>> Hi,
>>>> could this be the issue ?
>>>>
>>>>
>>>>   From the habndbook:
>>>>
>>>>      If you do NOT authenticate against a peer host, then the caller
>>>> CLI is
>>>> put into the From and P-Asserted-Identity headers, e.g. "+4312345"
>>>> <sip:+4312345 at your-domain.com>. If you DO authenticate, then the From
>>>> header is "+4312345" <sip:your_peer_auth_user at your_peer_auth_realm>
>>>> and
>>>> the P-Asserted-Identity header is as usual like
>>>> <sip:+4312345 at your-domain.com>. So for presenting the correct CLI in
>>>> CLIP no screening scenarios, your peering provider needs to extract
>>>> the
>>>> correct user either from the From Display-Name or from the
>>>> P-Asserted-Identity URI-User.
>>>>
>>>>
>>>>
>>>> Otherwise please give us more information about your peer
>>>> configuration
>>>> and the call scenario.
>>>>
>>>> Daniel
>>>>
>>>>
>>>>
>>>> On 07/07/2014 10:04 AM, Jorge Fresneda - Ibersontel wrote:
>>>>> Hello,
>>>>>
>>>>> I have a problem in version 2.8 with outgoing calls. In the from
>>>>> field  goes "source@ <pbx_ip>"  instead of  "source@ <sipwise_ip>".
>>>>>
>>>>> What may be because this problem?
>>>>>
>>>>> Thank you very much.
>>>>> Regards
>>>>> Jorge
>>>>>
>>>>> _______________________________________________
>>>>> Spce-user mailing list
>>>>> Spce-user at lists.sipwise.com
>>>>> http://lists.sipwise.com/listinfo/spce-user
>>>> _______________________________________________
>>>> Spce-user mailing list
>>>> Spce-user at lists.sipwise.com
>>>> http://lists.sipwise.com/listinfo/spce-user
>>>
>>> _______________________________________________
>>> Spce-user mailing list
>>> Spce-user at lists.sipwise.com
>>> http://lists.sipwise.com/listinfo/spce-user
>>
>> _______________________________________________
>> Spce-user mailing list
>> Spce-user at lists.sipwise.com
>> http://lists.sipwise.com/listinfo/spce-user
>
>
> _______________________________________________
> Spce-user mailing list
> Spce-user at lists.sipwise.com
> http://lists.sipwise.com/listinfo/spce-user