[Spce-user] Outgoing Call - Problem

[Jorge Fresneda - Ibersontel]

Hi,

If, from the PBX I receive "wrong" from. But if another log PBX sipwise 
2.4 (instead of 2.8), it works correctly. I need configure a 
"fromdomain" parameter on siptrunk PBX --> SPCE ??

Regards,
Jorge

El 07/07/2014 10:51, Daniel Grotti escribió:
> Hi,
> it's just a guess.
> Do you really receive the INVITE from your subscriber with the "wrong"
> FROM domain ?
> If so, this is something you need to change on subscriber side.
> Don't know which parameter you need to set, don't know even the client.
>
> Daniel
>
>
>
>
>
>
> On 07/07/2014 10:44 AM, Jorge Fresneda - Ibersontel wrote:
>> Hi Daniel,
>>
>> What parameter need to look to change this within the subscriber?
>>
>> Regards
>> Jorge
>>
>> El 07/07/2014 10:27, Daniel Grotti escribió:
>>> Hi,
>>> looks like your subscriber is setting that From domain.
>>> Usually, if you register a client to a domain, the From should look like
>>> as you said:
>>>
>>> from: <sip:91111111 at SCPE_DOMAIN>
>>> to: <sip: 922222222@<SPCE_DOMAIN>
>>>
>>> before going to the PEER:
>>>
>>> from: <sip:91111111 at SCPE_DOMAIN>
>>> to: <sip: 922222222@<PEER_IP>
>>>
>>>
>>> Daniel
>>>
>>>
>>>
>>>
>>>
>>> On 07/07/2014 10:18 AM, Jorge Fresneda - Ibersontel wrote:
>>>> Hi Daniel,
>>>>
>>>> The problem is not with the CLI, it is with the @ your-domain. For
>>>> example:
>>>>
>>>>
>>>> Sipwise Address: 120.23.1.1
>>>> Address PBX (subscriber): 192.168.1.2
>>>>
>>>> When I launch a call from the field is as follows:
>>>>
>>>> from: <sip:91111111 at 192.168.1.2>
>>>> to: <sip: 922222222@<carrier_ip>
>>>>
>>>>
>>>> The from should be <sip:91111111 at 120.23.1.1> for the carrier to accept
>>>> calls.
>>>>
>>>>
>>>> Thanks
>>>> Regards,
>>>> Jorge
>>>>
>>>>
>>>>
>>>> El 07/07/2014 10:12, Daniel Grotti escribió:
>>>>> Hi,
>>>>> could this be the issue ?
>>>>>
>>>>>
>>>>>    From the habndbook:
>>>>>
>>>>>       If you do NOT authenticate against a peer host, then the caller
>>>>> CLI is
>>>>> put into the From and P-Asserted-Identity headers, e.g. "+4312345"
>>>>> <sip:+4312345 at your-domain.com>. If you DO authenticate, then the From
>>>>> header is "+4312345" <sip:your_peer_auth_user at your_peer_auth_realm>
>>>>> and
>>>>> the P-Asserted-Identity header is as usual like
>>>>> <sip:+4312345 at your-domain.com>. So for presenting the correct CLI in
>>>>> CLIP no screening scenarios, your peering provider needs to extract
>>>>> the
>>>>> correct user either from the From Display-Name or from the
>>>>> P-Asserted-Identity URI-User.
>>>>>
>>>>>
>>>>>
>>>>> Otherwise please give us more information about your peer
>>>>> configuration
>>>>> and the call scenario.
>>>>>
>>>>> Daniel
>>>>>
>>>>>
>>>>>
>>>>> On 07/07/2014 10:04 AM, Jorge Fresneda - Ibersontel wrote:
>>>>>> Hello,
>>>>>>
>>>>>> I have a problem in version 2.8 with outgoing calls. In the from
>>>>>> field  goes "source@ <pbx_ip>"  instead of  "source@ <sipwise_ip>".
>>>>>>
>>>>>> What may be because this problem?
>>>>>>
>>>>>> Thank you very much.
>>>>>> Regards
>>>>>> Jorge
>>>>>>
>>>>>> _______________________________________________
>>>>>> Spce-user mailing list
>>>>>> Spce-user at lists.sipwise.com
>>>>>> http://lists.sipwise.com/listinfo/spce-user
>>>>> _______________________________________________
>>>>> Spce-user mailing list
>>>>> Spce-user at lists.sipwise.com
>>>>> http://lists.sipwise.com/listinfo/spce-user
>>>> _______________________________________________
>>>> Spce-user mailing list
>>>> Spce-user at lists.sipwise.com
>>>> http://lists.sipwise.com/listinfo/spce-user
>>> _______________________________________________
>>> Spce-user mailing list
>>> Spce-user at lists.sipwise.com
>>> http://lists.sipwise.com/listinfo/spce-user
>>
>> _______________________________________________
>> Spce-user mailing list
>> Spce-user at lists.sipwise.com
>> http://lists.sipwise.com/listinfo/spce-user
>
> _______________________________________________
> Spce-user mailing list
> Spce-user at lists.sipwise.com
> http://lists.sipwise.com/listinfo/spce-user