Hello all: Letter k. below was the issue. By bringing the config.yml
from the original server and putting it on the recovery server that was
the issue.
In previous duplications this always worked.
So I put back the original config.yml and ran ngcpcfg apply and now the
system is running correctly. (the purpose of using the original
config.yml was to retain settings and configuration )
I hope this info can be helpful in the future to other list users. We
can consider this questions resolved.
Thanks
Kevin
From: Kevin Masse
Sent: Thursday, October 30, 2014 2:32 PM
To: Kevin Masse; Spce-user at lists.sipwise.com
Subject: RE: [Spce-user] Recovery Question PKG 2.8
It appears that the problem is this:
Not executing command for kamailio-proxy: invalid configuration file!
-e
0(3332) : <core> [cfg.y:3549]: parse error in config file
/etc/kamailio/proxy/proxy.cfg, line 2068, column 47: syntax error
0(3332) : <core> [cfg.y:3549]: parse error in config file
/etc/kamailio/proxy/proxy.cfg, line 2068, column 47: bad expression
0(3332) : <core> [cfg.y:3546]: parse error in config file
/etc/kamailio/proxy/proxy.cfg, line 2079, column 2-3: bad command
ERROR: bad config file (3 errors)
Thanks
Kevin
From: Spce-user [mailto:spce-user-bounces at lists.sipwise.com] On Behalf
Of Kevin Masse
Sent: Thursday, October 30, 2014 1:36 PM
To: Spce-user at lists.sipwise.com
Subject: [Spce-user] Recovery Question PKG 2.8
Good afternoon Group:
I have a question relating to moving services to another server so I
will outline the process used which is not working as it did in the
past.
In the past I was able to move to another system using the following
steps.
a.) mysqldump -p --databases billing provisioning kamailio accounting
carrier ngcp sipstats > /tmp/backup.sql
This was preparing the databases to move to a new server.
b.) Perform the standard Debian Squeeze installation (basic server)
as instructed & Patch system, example: BASH issue
c.) PKG=ngcp-installer-2.8.deb
d.) wget http://deb.sipwise.com/spce/${PKG}
<http://deb.sipwise.com/spce/$%7bPKG%7d>
e.) dpkg -i ${PKG}
f.) ngcp-installer
g.) ngcp-network --set-interface=eth0 --ip=auto --netmask=auto
h.) ngcp-network --move-from=lo --move-to=eth0 --type=web_ext
--type=sip_ext --type=rtp_ext --type=ssh_ext
i.) edit /etc/network/interfaces (setting the IP information
required for this server)
j.) move the database over from the backup and process: mysql -p
</tmp/backup.sql
k.) move over the config.yml from the previous server
l.) run ngcpcfg apply to verify everything sets up ok
m.) reboot to make sure everything is listening ok
NOTE: The IP address of the duplicated server is also listed in the
domain list.
Is there any reason to think this process would not work today as it did
in the past?
If the original install was done according to the steps above on Feb 4th
2014 would the distribution be different now in 2.8 that is causing a
difference in the system?
Is there a way to install the version of 2.8 that was being downloaded
on Feb 4 2014 compared to the newer 2.8 that is currently available?
Thank you
Kevin
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sipwise.com/pipermail/spce-user_lists.sipwise.com/attachments/20141030/40a8127c/attachment-0001.html>