[Spce-user] Registering to domain name

[Daniel Grotti]

Hi,
currently we have other priority, so I would say it's on low prio.
It's a little bit more complicated, since we need to patch SEMS somehow,
in order to check the DB, take the outbound_socket used by that peer and
the add P-Out-Socket ticket in the REGISTER message, so LB can use the
right socket.


--
Daniel Grotti
VoIP Engineer


Sipwise GmbH
Europaring F15 | 2345 Brunn am Gebirge, Austria | www.sipwise.com

On 11/06/2015 05:31 PM, Serge S. Yuriev wrote:
> Hi,
> 
> That do you think how far this is? Is it low or high priority?
> If I understood correctly LB should rewirte contact and send it from
> selected socket. And it does this partially if request comes with
> localhost in contact.
> 
> On 02/11/15 18:08, Daniel Grotti wrote:
>> Hi,
>> This is not possible currently.
>> Cause REGISTER for the peer is sent by SEMS to LB and from LB to the
>> provider. And SEMS does not check the outbound_socket for that peer so
>> it uses the default one.
>>
>> We would need to improve that. I will add this in our TODO list.
>>
>>
>>
>> -- 
>> Daniel Grotti
>> VoIP Engineer
>>
>>
>> Sipwise GmbH
>> Europaring F15 | 2345 Brunn am Gebirge, Austria | www.sipwise.com
>>
>> On 11/02/2015 04:01 PM, Serge S. Yuriev wrote:
>>> Hi,
>>>
>>> Missed right reply key, sorry :(
>>> Yes, I already set outbound_socket as required but SPCE sending register
>>> from default one :(
>>> We have pretty non-standart peering w/uplink via internal network
>>> 10.0.64.100 <--> 82.x.x.178
>>>
>>> On 02/11/15 17:46, Daniel Grotti wrote:
>>>> Please,
>>>> reply to the mailing list.
>>>> On peer preferences you have outbound_socket, so you can use the
>>>> preferred socket for outbound messages.
>>>> Not sure if the socket is used for outbound REGISTER as well.
>>>>
>>>> Not sure if I have uderstood right what you want to achieve, though.
>>>>
>>>> -- 
>>>> Daniel Grotti
>>>> VoIP Engineer
>>>>
>>>>
>>>> Sipwise GmbH
>>>> Europaring F15 | 2345 Brunn am Gebirge, Austria | www.sipwise.com
>>>>
>>>> On 11/02/2015 02:56 PM, Serge S. Yuriev wrote:
>>>>> Hi,
>>>>>
>>>>> Sorry for my ugly English :(
>>>>> I mean we try to register to provider with multiple addresses under
>>>>> one
>>>>> name.
>>>>> And we need to use specific interface for that.
>>>>>
>>>>> On 02/11/15 16:28, Daniel Grotti wrote:
>>>>>> Hi,
>>>>>> the SIP domain used in registration MUST be one of you SIP domain
>>>>>> configured in the platform.
>>>>>> Then you should configure you DNS in order to resolve that SIP
>>>>>> domain to
>>>>>> one of your IP listening on port 5060.
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> -- 
>>>>>> Daniel Grotti
>>>>>> VoIP Engineer
>>>>>>
>>>>>>
>>>>>> Sipwise GmbH
>>>>>> Europaring F15 | 2345 Brunn am Gebirge, Austria | www.sipwise.com
>>>>>>
>>>>>> On 11/02/2015 02:25 PM, Serge S. Yuriev wrote:
>>>>>>> Hello,
>>>>>>>
>>>>>>> Our uplink ask us to register via domain name which resolves to
>>>>>>> multiple
>>>>>>> addresses.
>>>>>>> All these addresses exists in SPCE config with socket configured
>>>>>>> but not
>>>>>>> used in registration process.
>>>>>>> How we could use designated socket for this?
>